药物相互作用研究在新药研发和审评决策中的应用

药物相互作用改变了剂量效应关系，可能会降低疗效或增加毒性，是临床应用中合并用药治疗时重要的考虑因素。预测具有临床意义的药物相互作用是药物研发过程中获益风险评估的重要环节。本文概述了药物研发过程中药物相互作用研究的目的和意义，体内和体外研究的主要内容；梳理分析了2020年国家药品监督管理局（National Medical Products Administration, NMPA）和美国食品药品监督管理局（Food and Drug Administration, FDA）批准上市的新药药物相互作用研究情况，旨在为我国药物研发过程中药物相互作用研究及其监管审评提供参考。     

BS960E高强钢激光-电弧复合焊接头氢脆行为研究

氢脆具有很强的微观组织敏感性,威胁着各类高强结构材料的安全服役.采用激光-电弧复合焊工艺对BS960E型高强钢进行焊接,并对接头在原位电化学充氢的条件下进行慢应变速率(10-5s-1)拉伸试验,结合微观组织和断裂特征进行分析并对接头的氢脆行为进行研究.结果 表明,焊接热循环所形成的富马氏体中的细晶区可以使接头表现出一定的氢脆敏感性,马氏体较大的氢扩散系数和较低的氢溶解度以及氢在晶界上的快速扩散是引起接头对氢脆敏感的主要原因,通过控制焊接工艺参数可抑制焊接热循环所引起的马氏体转变量,能够降低BS960E型高强钢激光-电弧复合焊接头的氢脆敏感性.     

汽油气相色谱模拟馏程的应用

介绍了用AC8612气相色谱仪对六个汽油组分馏程分析的应用情况,结果表明:该方法的重复性和准确性都较好,与D86相比,结果满足方法的再现性要求,但对于差值大于3℃的点,应定期进行修正,以使结果更准确,该方法用于炼油厂各装置汽油组分馏出口的日常质量监测分析,可以提高分析效率并减少劳动强度。     

HPLC法测定伐地昔布的有关物质

建立高效液相色谱法检测伐地昔布的有关物质.采用α-酸性糖蛋白键合硅胶的手性色谱柱,以乙腈-醋酸铵缓冲液(0.01 mol/L,pH4.0)作为流动相进行梯度洗脱,检测波长215 nm.伐地昔布与5个已知杂质均可达到基线分离,在各自浓度范围内线性关系良好,平均回收率95.13％～99.77％,RSD1.10％～1.77％,检测限0.017 9～0.060 1 μg/mL,定量限0.059 7～0.200 0 μg/mL.方法专属性强,准确度好,灵敏度高,可为伐地昔布的质量控制及后续分离提纯和帕瑞昔布的质量控制提供指导.     

装配式混凝土木混合结构体系简述

上海电气研混凝土(如皋)建筑科技有限公司——建筑工业化智能创新基地项目,采用装配式混凝土木混合结构,该结构是一种新型的建筑结构体系.其承重的部分采用混凝土结构且可在工厂进行预制,围护结构采用木材制成,可在满足使用等功能的同时降低造价、减轻自重、保护环境,具有很大的发展潜力.     

Methods and mechanisms for uniformly refining deformed mixed and coarse grains inside a solution-treated Ni-based superalloy by two-stage heat treatment

The uniform refinement mechanisms and methods of deformed mixed and coarse grains inside a solution-treatment Ni-based superalloy during two-stage annealing treatment have been investigated.The two-stage heat treatment experiments include an aging annealing treatment(AT)and a subsequent recrystallization annealing treatment(RT).The object of AT is to precipitate some δ phases and consume part of storage energy to inhibit the grain growth during RT,while the RT is to refine mixed and coarse grains by recrystallization.It can be found that the recrystallization grains will quickly grow up to a large size when the AT time is too low or the RT temperature is too high,while the deformed coarse grains cannot be eliminated when the AT time is too long or the RT temperature is too low.In addition,the mixed microstructure composed of some abnormal coarse recrystallization grains(ACRGs)and a large number of fine grains can be observed in the annealed specimen when the AT time is 3 h and RT tem-perature is 980℃.The phenomenon attributes to the uneven distribution of δ phase resulted from the heterogeneous deformation energy when the AT time is too short.In the regions with a large number of δ phases,the recrystallization nucleation rate is promoted and the growth of grains is limited,which results in fine grains.However,in the regions with few δ phases,the recrystallization grains around grain boundaries can easily grow up,and the new recrystallization nucleus is difficult to form inside grain,which leads to ACRGs.Thus,in order to obtain uniform and fine annealed microstructure,it is a prereq-uisite to precipitate even-distributed δ phase by choosing a suitable AT time,such as 12 h.Moreover,a relative high RT temperature is also needed to promote the recrystallization nucleation around δ phase.The optimal annealing parameters range for uniformly refining mixed crystal can be summarized as:900℃×12 h+990℃×(40-60 min)and 900℃×12 h+1000℃×(10-15 min).     

Dealloying corrosion of anodic and nanometric Mg41Nd5 in solid solution-treated Mg-3Nd-1Li-0.2Zn alloy

The microstructure and chemical compositions of the solid solution-treated Mg-3Nd-1Li-0.2Zn alloy were characterized using optical microscope,scanning electron microscope(SEM),transmission electron microscope(TEM),electron probe micro-analyzer(EPMA)and X-ray photoelectron spectroscopy(XPS).The corrosion behaviour of the alloy was investigated via electrochemical polarization,electrochemical impedance spectroscopy(EIS),hydrogen evolution test and scanning Kelvin probe(SKP).The results showed that the microstructure of the as-extruded Mg-3Nd-1Li-0.2Zn alloy contained α-Mg matrix and nanometric second phase Mg41 Nd5.The grain size of the alloy increased significantly with the increase in the heat-treatment duration,whereas the volume fraction of the second phase decreased after the solid solution treatment.The surface film was composed of oxides(Nd2O3,MgO,Li2O and ZnO)and carbonates(MgCO3 and Li2CO3),in addition to Nd.The as-extruded alloy exhibited the best corrosion resistance after an initial soaking of 10 min,whereas the alloy with 4h-solution-treatment possessed the lowest corrosion rate after a longer immersion(1 h).This can be attributed to the formation of Nd-containing oxide film on the alloys and a dense corrosion product layer.The dealloying corrosion of the second phase was related to the anodic Mg41Nd5 with a more negative Volta potential relative to α-Mg phase.The preferential corrosion of Mg41Nd5 is proven by in-situ observation and SEM.The solid solution treatment of Mg-3Nd-1Li-0.2Zn alloy led to a shift in corrosion type from pitting corrosion to uniform corrosion under long-term exposure.     

基于数据融合与迁移学习的学生表情识别研究

学生表情逐渐成为感知学生状态的重要途径,因此准确的识别学生表情因具有重要价值而受到广泛的关注.本文针对学生表情识别这一问题,提出基于数据融合与迁移学习的识别模型,该模型融合3个数据集,以解决学生表情数据缺乏与多样性问题,同时引入迁移学习来提升预测精度.在数据集及实际学生表情图像上的实验结果表明,本文提出的模型可以准确识别学生表情,提升了预测精度.     

地铁机电安装绩效领先指标自动预测方法

目前的绩效领先指标的预测中对样本数据的平稳性考虑不足,样本数据波动性大,影响最终的预测准确性.因此提出地铁机电安装绩效领先指标自动预测方法,首先对影响项目绩效的指标进行拟定描述,确定指标后使用Lasso方法来确定其中变量对绩效指标影响程度,然后使用ADF单位根检验法对相关波动数据进行平稳化处理,运用BP神经网络技术来实现自动预测.为了验证设计方法是否满足设计目的 ,设计实验,使用某地铁机电安装工程的数据作为样本数据并进行自动预测,预测结果显示:本文设计方法对比其他方法结果更接近实际值,设计满足设计要求.     

伊拉克A油田Asmari组混积型碳酸盐岩储层隔夹层研究

伊拉克A油田Asmari组为大型混积型碳酸盐岩油藏,发育灰岩、白云岩、砂岩、泥岩和硬石膏等多种岩性,储层复杂、非均质性强,存在多种类型的隔夹层。基于岩心、薄片、测井和分析测试等资料,对研究区隔夹层类型及特征展开综合分析,识别出了泥岩、硬膏岩和泥-微晶碳酸盐岩3类隔夹层。泥岩和硬石膏致密无孔隙、基本不具有渗流能力,对流体流动可以起到阻挡作用;泥-微晶碳酸盐岩属于细粒碳酸盐岩沉积,孔隙度低,但一般裂缝较发育,具有一定渗流能力,不能对流体起到有效的隔挡作用。硬石膏主要在油田中部及北部A段发育,其对油田北部储层纵向连通起到一定隔挡作用,导致纵向压力衰竭不一致。泥岩主要在C段顶部、B4和B1层发育,平面上主要在油田南部较发育。C段顶部发育一套厚度较大、稳定分布的泥岩隔层,将C段和上部B段及A段分隔为两个独立的油水系统,并有效阻挡了C段水层锥进到B段;B4和B1层泥岩较发育,但由于油田南部区域断层和裂缝较发育,导致泥岩隔夹层未能起到有效隔挡作用。搞清研究区隔夹层类型、分布及是否起隔挡作用,对A油田各区域各小层有效动用开发、见水规律研究具有很好的指导意义。